Exterior Toyota Corolla Read Door Panel Removal

Toyota Corolla Repair Transmission: Overhaul

Hint

:

• installation is in the reveres order of the removal. Only the installation is indicated merely when information technology has a signal.
• In the rh side, work in the aforementioned procedure as in the lh side.

1. Remove rear armrest assy lh

1. Using a screwdriver, remove the rear armrest.

Hint

: tape the screwdriver tip earlier apply.

2. Remove power window regulator switch assy rear (w/ power window)

1. Using a screwdriver, remove the power window regulator switch assembly.

Hint

: tape the screwdriver tip before employ.

3. Remove rear door window regulator handle assy (w/o ability window)

1. Using a shop rag, remove the snap ring.
2.  remove the rear door window regulator handle and plate.

four. Remove rear door trim board sub�assy lh

1. Remove the 3 screws.
2.  using a screwdriver, disengage the clips, then pull the trim board upwards to remove information technology.

Hint

: tape the screwdriver tip earlier use.

v. Remove rear door inside handle sub�assy lh

1. Remove the inside handle and then disconnect the 2 cables from the inside handle.

half-dozen. Remove rear door service hole encompass lh

1.  disconnect each connector and remove the rear door service hole cover.

Discover

: remove the remaining record on the body side.

seven. Remove rear door belt moulding assy lh

8. Remove rear door drinking glass run lh

1.  remove the rear door glass run.

9. Remove rear door inside console plate lh

1. Remove the 4 screws and rear door within panel plate.

10. Remove rear door window division bar sub�assy lh

1. Remove the 2 bolts and screw.
2. rotate the rear door window division bar by xc� and pull it upward, as shown in the analogy.

11. Remove rear door quarter window glass lh

1.  remove the rear door quarter window drinking glass.

   Notice

   : exercise not damage the glass.

2.  remove the quarter window weatherstrip from the glass.

12. Remove rear door glass sub�assy lh

Hint

: insert a shop rag inside the door panel to forbid the glass from being scratched.

1.  open up the door glass.
2.  tilt the door glass and disconnect the roller of the regulator from the channel to remove the door drinking glass.

Notice

: do non harm the door drinking glass.

Hint

: pull the glass upwards to remove it.

thirteen. Remove rear door window regulator sub�assy lh (w/o power window)

1.  loosen the 4 bolts.

   Find

   : when the bolts are removed, the rear door window regulator might drop and be deformed.

2.  remove the 4 bolts and rear door window regulator.

fourteen. Remove rear door window regulator sub�assy lh (due west/ ability window)

1. Disconnect the window regulator connector.
2.  loosen the 4 bolts.

   Detect

   : when the bolts are removed, the rear door window regulator might drop and be deformed.

3.  remove the iv bolts and rear door window regulator.

15. Remove power window regulator motor assy lh

1.  using a torx wrench (t30), remove the 3 screws and the motor associates.

xvi. Remove rear door lock assy lh (west/o power door lock)

1.  using a torx wrench (t30), remove the 3 screws and the rear door lock assembly.

17. Remove rear door w/motor lock assy lh (w/ ability door lock)

1. Disconnect the power door lock connector.
2.  using a torx wrench (t30), remove the 3 screws and the power door lock assembly.

18. Remove rear door outside handle comprehend lh

1.  using a torx wrench (t30), loosen the screw and remove the rear door outside handle encompass.

xix. Remove rear door outside handle assy lh

1. Pull and concur the release plate of the exterior handle frame, every bit shown in the illustration.

2. Pushing the outside handle in the pointer marking direction as shown in the analogy, remove the exterior handle.

Notice

: if the release plate is not pulled and held when removing the outside handle, and so the release plate will interfere with the exterior handle and information technology will damage the release plate.

20. Remove rear door outside handle frame sub�assy lh

1. Using a torx wrench (t30), loosen the spiral.
2.  using pliers, disengage the clips and remove the outside handle frame, as shown in the illustration.

Observe

: be certain to remove the outside handle together with the clips, because the clips will be damaged if the clips remain attached to the door panel.

21. Remove rear door weatherstrip lh

1.  remove the door console side bolt and disconnect the rear door check assembly.
2.  using a screwdriver, remove the weatherstrip.

Hint

: tape the screwdriver tip earlier use.

22. Install rear door weatherstrip lh

1.  install the weatherstrip.
2.  install the rear door cheque assembly with the door panel side bolt.

   Torque: 5.5 N�m (56 kgf�cm, 49 in.�Lbf)

23. Install rear door exterior handle frame sub�assy lh

1.  using a torx wrench (t30), install the outside handle frame with the spiral.

   Torque: four.0 North�yard (41 kgf�cm, 35 in.�Lbf)

24. Install rear door outside handle embrace lh

1.  using a torx wrench (t30), install the exterior handle embrace with the screw.

   Torque: 4.0 N�g (41 kgf�cm, 35 in.�Lbf)

25. Install rear door lock assy lh (w/o power door lock)

1.  utilise mp grease to the sliding and rotating parts of the door lock.
2.  utilise adhesive to the 3 screws.

   Part no.08833�00070, Three bond 1324 or equivalent

3.  using a torx wrench (t30), install the lock assembly with the 3 screws.

   Torque: 5.0 N�m (51 kgf�cm, 44 in.�Lbf)

26. Install rear door w/motor lock assy lh (west/ ability door lock)

1.  install a new door lock wire harness packing.

Discover

:

• if reusing the removed lock with rear door motor, the packing in the connecting part should exist replaced with a new ane.
• Exist careful that no grease and dirt will stick to the packing surface in the connecting office.
• Reusing the removed packing or using a damaged packing will crusade water to penetrate through the connecting office, and it volition upshot in a malfunction of the door lock.

2.  engage the lock assembly with door motor with the release plate of the exterior handle, and so set it to the door panel.

   Observe

   : brand certain that the release plate of the outside handle frame is securely engaged with the lock associates.

3.  apply mp grease to the sliding and rotating parts of the door lock.
4.  apply agglutinative to the three screws.

   Part no.08833�00070, Iii bond 1324 or equivalent

5. Using a torx wrench (t30), install the door lock assembly with the 3 screws and bolt.

   Torque: 5.0 N�chiliad (51 kgf�cm, 44 in.�Lbf)

6.  connect the power door lock connector.

27. Install power window regulator motor assy lh (w/ power window)

1.  using a torx wrench (t30), install the ability window regulator motor assembly with the three screws.

   Torque: five.four North�m (55 kgf�cm, 48 in.�Lbf)

28. Install rear door window regulator sub�assy lh (w/o ability window)

1. Use mp grease to the sliding and rotating parts of the window regulator.

   Notice

   : do not utilise grease to the spring of the window regulator.

2.  install the rear door window regulator with the iv bolts.

   Torque: 8.0 N�m (82 kgf�cm, 71 in.�Lbf)

29. Install rear door window regulator sub�assy lh (w/ power window)

1. Apply mp grease to the sliding and rotating parts of the window regulator.

   Notice

   : practice not apply grease to the jump of the window regulator.

2.  apply the window regulator to the 4 regulator installation holes on the front door panel, temporarily install the window regulator with the installation bolts.
3.  tighten the 4 bolts and the temporarily installed bolt.

   Torque: 8.0 N�chiliad (82 kgf�cm, 71 in.�Lbf)

4.  connect the window regulator connector.

thirty. Install rear door window division bar sub�assy lh

1. Insert the door window segmentation bar to the door console, and then rotate information technology by 90�.
2.  install the bolt and 3 screws.

   Torque:
   bolt a: half dozen.2 N�m (63 kgf�cm, 55 in.�Lbf)

31. Install rear door glass sub�assy lh (w/ power window)

Hint

: insert a shop rag inside the door panel to prevent the glass from being scratched.

1.  tilt the door glass and connect the roller of the regulator to the glass channel to install the door glass.
2.  inspect the power window operation.

1.  Connect the ability window switch to the wire harness and plough the ignition switch on.
2.  Repeat up and downwardly operation several times in the manual operation.
3.  Check if auto up "auto downwards operates in the automatic functioning.

Hint

:

• note that the jam protection function does not operate just afterwards resetting.
• Reset the regulator once again when performing the reverse functioning after endmost the window fully in the auto up functioning.

32. Audit power window function (w/ power window)

33. Install rear door service pigsty embrace lh

1.  install a new service hole cover to the door panel.

Hint

:

• when installing the service pigsty encompass, pull out the links and connectors through the service pigsty encompass.
• At that place should exist no wrinkles or folds after attaching the service pigsty embrace.
• After attaching the service hole cover, sealing condition should be confirmed.

34. Install rear door window regulator handle assy (due west/o ability window)

1. Install the regulator handle with the snap ring.

Hint

: with the door window fully closed, install the plate and regulator handle with the snap ring as shown in the illustration.

Adjustment

Hint: in the rh side, piece of work in the same procedure as in the lh side. Since the centering commodities is used as a door side hinge commodities, the door swivel cannot exist adjusted with it on. Substitute the b ...

Baggage compartment door

Adjustment 1. Inspect baggage compartment door panel sub�assy  check that the clearance is within the standard value. 2. Adjust baggage compartment door panel sub�assy For forwa ...

Other materials:

Power bespeak socket assy
Replacement Hint: components: 1. Remove floor shift shift lever knob sub�assy (m/t transaxle) 2. Remove panel console upper 3. Remove power point socket assy Turn the socket in the circumference direction as shown the illustration, disengage the claw between the socket and the ability ...

Front suspension
Preparation Sst Recomended tools Equipment ...

Inspection procedure
ane Bank check p squib circuit(airbag sensor assy center � instrument panel rider airbag assy) Disconnect the negative (�) terminal cablevision from the battery, and expect at least for ninety seconds.  disconnect the connectors between the airbag sensor assy middle and the instrument console pas ...

Exterior Toyota Corolla Read Door Panel Removal

Source: https://www.tcorolla.net/overhaul-1423.html

Share this post